Sep
Bear Kit
Posted in Uncategorized | No Comments »Bear Kit
what does case machining in order to fit a big bore kit imply with an atv?
i have a 300ex that needs case machining to fit a big bore cylinder i bought, what all does this case machining entitle? i know the goal is to accomodate a sleeve with a larger O.D. but does this have to be done professionally or can it be done with a dremel or such as long as one is careful and doesnt get any metal shavings into the bottom end of the motor?
Your question about case clearancing to accomodate the larger cylinder sleeve diameter of a Big Bore kit seems to have mistaken as regarding some other operation.
Not only CAN it be done by hand,but on engines where it’s Practical to do so it’s the method of choice.
A trx 300 is definitely in the “practical” category.
As far as any matter of “Precision”…….
It’s a Big,Gaping SQUARE Maw of a hole,,,lol
How Precise is “Putting a round Peg into a square hole” EVER going to be?
They only have radial clearance arcs cut into each side of the square to accept the round cylinder liner.
They’re only a few degrees of arc,,,,just a small “piece” of a circle.
What’s even easier,,is that they’re SHALLOW,,,crancase deck is fairly thin in those areas.
So no need to cut very DEEP into case.
The One tight spot is on the REAR of the case,,,because it’s clearance cut runs full depth and blends into what becomes Crankshaft Baffle.
As Daunting as that appears,,,it does NOT require a Full Depth cut.
Only deep enough so that Cyl Sleeve doesnt shoulder/bottom out on Crankcase.
Most all Big Bore Kits are made with SHORTER sleeves,,,so that they can be used with Stroker Kits.
The Shorter Skirt accomodates the Rod Swing of the longer stroke.
One thing,,,You CANT use a Dremel.
Too Small,note nough power,,,
It will most likely be destroyed before job is completed.
Any decent 1/4″ 5~7A++ Hand Grinder will do it easily
…………………………………………..
You NEED the power and RPM of a REAL grinder.
Air powered die grinders are CHEAP,,,if you have access to an air compressor with the capacity to run it.
Electric Die Grinders are Big,Heavy,Expensive and Ferocious Eaters,,,, which is generally Just the Ticket!
New,Quality ones are waaay too pricey,,,$150~200 +++>>>>
There’s a OLD Sears,a Dumore,a couple of Milwaukees,etc on Ebay….they’ll all go off over $50 Im sure,,probly More.
Here’s some Chinese Crap,,,,”2 for 1″,,,for REALLY Stoopid Cheap.
You would likely NEED Both to finish the job,,,lol
What caught my interest is that they are claimed to be 5 Amp tools.
Most similar junk is only around 2A or so.
(Dremel>>less than 1 Amp)
The “Pro Stuff” is 7~10~12 +++amp range.
Just to put various available Power Levels into some sort of perspective.
If you WANNA Risk the $20~30 for a couple of Alledgedly Suitable Die Grinders,,,,,,Having a Pair makes it a worthwile gamble in my opinion.
I ‘bleive you’d have decent odds of at least getting the job done.
NO RECCO,,,I’m just passing along what I stumbled upon
while “shopping” to be able to at least give you an idea.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=300146985989&ssPageName=STRK:MEWA:IT&ih=020
Heres other examples of the Type/Class of tool you really need:
“megadremel”,,Foot Long,,4~5lb stuff
http://cgi.ebay.com/Milwaukee-5196-Heavy-Duty-11-Amp-2-Die-Grinder_W0QQitemZ140151130348QQcmdZViewItem?hash=item140151130348
http://www.makita.com/menu.php?pg=product_det&tag=906H
http://www.dumorecorp.com/grinder.htm#hg
(#10 type)
……………………………………………..
Cutters
Here’s some examples from Long Co.
http://www.helongco.com/
My Choices would be from the NF Series:
http://www.helongco.com/nfburs/nfall.html
*Cylindrical NF in SA3 Size for Guided Router or FreeHand work
and
*Taper Radius End NF in SL3 Size>>IF I was gonna FreeHand Grind it,,,,,and IF Rear Cut Access looked to be a Potential Problem at it’s extreme end depth.
Depending upon the Actual Situation with the potentially “Tight” REAR CUT,,,,
I Might chose a
Cylindrical Radius End NF .
It will serve same as a Flat end on the Front and Sides,,,
But Leave a Radiused Step on less-than Full Depth cuts,,,rather than a square shoulder.
The extra working clearnce of it’s radiused Nose MIGHT be enough to Clear the CRANKSHAFT at extreme depth,,,enough to allow an adequately Deep Cut—-if necessary.
Using “cheap” HighSpeedSteel ones from hardware store are a false economy,,,ESPECIALLY with Aluminum.
They WILL work though—even if not very well
…………………………………..
It’s a waste of time to make a router base and guide,,,especially for a 300ex type crankcase.
Easiest,fastest most practical method remains a hand grinder.
………………
.001 to .002 Clearance is PISTON SKIRT -to-CYLINDER WALL range.
You cannot use anything even near that tight for crankcase releif.
Expansion and distortion would “pinch” the liner and cause really odd reliability problems
You need about 10 or 15 TIMES that much.
.020~.030
20 or 30 Thousandths,,,NOT merely 1 or 2.
1/2 to 3/4 MM,,,,Minimum.
…………………………
As you stated,,,SHIELDING the bottom end is critical.
Cramming Shop Towels into engine Does NOT constitute effective shielding.
Easy to keep shavings from getting into motor while cutting.
TUFFER to avoid SPILLING them when you go to Remove the packing.
Time/Effort spent doing a neat,clean shielding and some THOUGHT before Removing it is all cheap insurance.
After packing /taping ,etc,,,,Add a couple Layers of single thickness material which can be removes AS a layer.
1st layer gets majority Out,,any spillage goes to Next.
And so on….
Pays to be ANAL
………………………………
Real quick and easy to do ,,IF you have a decent grinder.
Nothing “Precision” about clearancing a case,,,nothing whatsoever.
It’s merely adding SPACE,,extra room.
The area and surfaces involved are Non Contact,,Non-Functional.
And in any event,,,a 300 ex is a Square Hole.
It only needs the existing clearnace cuts re-radiused a bit.
Try to be workmanlike,of course
But as long as the minimum clearance is achieved,,,Engine dont care if was Cut with a Hammer and Chisel.
Unless it is I who misunderstand what your project is,,,
and You’re asking about something OTHER THAN clearancing a crankcase to accept a larger diameter Cylinder Sleeve of a Big Bore Kit.
|
|
MAKE YOUR OWNMINI TEDDY BEAR KIT AND BOOK NIB $1.50 |
|
|
BUILD A BEAR DOCTOR/NURSE TOY MEDICAL KIT BAG 6 PIECE $7.95 |
|
|
BUILD A BEAR WORKSHOP mini SOCCER STAR KIT Plush Basic $7.99 |
|
|
Build a Bear Workshop Create a Bear 7″ New Complete Kit $9.99 |
|
|
RUPERT BEAR TAPESTRY KIT $7.35 |
|
|
NIB BUILD A BEAR WORKSHOP KIT WITH OUTFIT 7 IN BEAR $5.99 |
|
|
Teddy Bear Kit – Complete Bear Making Kit $8.00 |
|
|
Teddy Bear Kit – Complete Bear Making Kit $8.00 |
|
|
BUILD A BEAR MEDICAL KIT $8.99 |
|
|
BUILD A BEAR FURBULOUS BEAUTY KIT $8.99 |
|
|
Teddy Bear Making Kit – New in Box – Makes 27cm Bear $0.91 |
|
|
NEEDLE FELTING KIT…MAKES 3 TEDDY BEARS..GREAT BUY $13.78 |
|
|
VINTAGE PENN TEDDY BEAR KITS (2 PANDA & 1 KOALA) LOT/3 $4.99 |
|
|
Artist Mini Teddy Bear Making Kit ~ 6″ Sydney $6.50 |
|
|
Build-A-Bear Workshop Bunny Kit $5.99 |
|
|
THE BERENSTAIN BEARS CREATE YOUR OWN MAMA BEAR KIT NEW $12.95 |
|
|
VINTAGE CARE BEARS QUILTED WALL HANGING KIT-NEW IN BOX $9.99 |
|
|
Vintage 1984 Care Bears Quilted Wall Hanging Kit NEW! $0.99 |
|
|
Bear Works – Make Your Teddy Bear Kit & Accessories $9.99 |
|
|
1996-1997 FRIENDS OF BOYD’S Bears F.o.B. Club Kit MIB $24.99 |
|
|
1998 FRIENDS OF BOYD’S Bears F.o.B. Club Kit MIB $24.99 |
|
|
2000 FRIENDS OF BOYD’S Bears F.o.B. Club Kit MIB $24.99 |
|
|
Stuff a Bear kit/John Deere/NEW!! $3.99 |
|
|
MUFFY BEAR “EGG DECORATING KIT” – TIN & HOLIDAY GOODIES $4.99 |
|
|
Lil Luvables Fluffy Factory & Bear Kit $5.00 |
|
|
NEW Mini Baby Bear Skins & Stuffing Kit FLUFFY FACTORY $9.99 |
|
|
Build A Bear European Hare with Kit NWT $24.99 |
|
|
Ted-Dee Bear ~ Jointed Teddy Bear Kit ~ Sandy Brown 20″ $4.99 |
|
|
MAKE YOUR BEAR KIT butterfly NEW $6.99 |
|
|
Pearl Louise Design Bear (2) Kit-Homespun Honey Bears $2.99 |
|
|
Teddy Bear Magazines and clothing kits $30.00 |
|
|
10pk Bears Clothes HAND Stuffables GIRL PARTY KIT $225.00 |
|
|
10pk Bears Clothes HAND Stuffable Girls Party Kit $225.00 |
|
|
8pk Bears Clothes &HAND Stuffables Boys Party Kit $227.25 |
|
|
TEDDY..BEAR ~ MAKING ~ KIT / FACTORY $22.96 |
|
|
Build A Bear ~Make And Play ~ Bunny Rabbit Kit ~Easter $10.95 |
|
|
Emily Farmer Bear Artist Kit – Circa 1904 Bear $9.00 |
|
|
Emily Farmer Bear Artist Kit – Vanilla Bear KIT $9.00 |
|
|
NIB Lil Luvables Studio Make your Own Bear/Doll Kit NEW $19.99 |
|
|
CREATE YOUR OWN BEAR IN MINUTES KIT~CREATIVE KIDS/TEDDY $17.25 |
|
|
Retired Boyds Bears: 1997-2001 FOB Collector Kits! $65.00 |
|
|
Retired Boyds Bears: 2004 FOB Collector Kit! $25.00 |
|
|
Retired Boyds Bears: 2003 FOB Collector Kit! $25.00 |
|
|
Retired Boyds Bears: 2002 FOB Collector Kit! $25.00 |
|
|
Build A Bear Deluxe House Kit GIrl NIB $29.95 |
|
|
Build A Bear Deluxe House Kit Boy NIB $29.95 |
|
|
BUILD A BEAR “TEAM” MAKE AN OUTFIT KIT 7″ BEAR/ANIMAL $2.99 |
|
|
LIL LUVABLES STUDIO BEAR AND DOLL MAKING KIT/W EXTRAS $26.99 |
|
|
NEW MAKE YOUR BEAR KIT $6.99 |
|
|
BUILD-A-BEAR DIMPLES BEAR STUFFING KIT MEMORY BOOK NIB $24.99 |